Mark this thread as Unsold
Audi Q7 Three-Piece Forged HRE Wheels Staggered Built to Your Spec!
#1
AudiWorld Member
Thread Starter
Join Date: Apr 2011
Location: The NH
Posts: 414
Likes: 0
Received 0 Likes
on
0 Posts
Three-Piece Forged HRE Wheels Staggered Built to Your Spec!
I've got a gorgeous set of 20" HRE 890R wheels in the correct bolt pattern and hub bore size for the 4L Q7 (2005-2015). Note: These will NOT fit the new 4M Q7s.
These are high-quality, lightweight forged three-piece wheels that cost over $5k new. The centers have been powdercoated with a beautiful metallic grey, and then clearcoated for durability. The powdercoat job is a 9.5/10; there are a few small imperfections either from dust or that occurred during shipping.
The fronts measure 20x10" with a 1.5" polished lip, and have a slightly more aggressive offset than stock, to give a bit more “poke” (+41). The lips are fully polished and look amazing.
The rears need to be rebuilt to fit a Q7, and here's where you could spec them how you'd like: I could do a standard 10", or a staggered fitment with a 10.5", or even an 11" width in the rear with some pretty aggressive offsets to get a nice flush look. I can vary the lips as well depending on how wide you’d like them.
Note: these wheels were re-drilled from a 120x5 to a 130x5 bolt pattern to fit the Q7. The re-drill job was done by Dominic at Dominant Engineering, who does meticulous work. This is a perfectly safe process: the Q7 is hub-centric, meaning it's the hubs themselves that "support" the weight of the vehicle.
If you're interested, I’d take an initial deposit of 10% via PayPal, and the balance would be due when they’re complete (about two weeks).
This is a great chance to get some high-quality wheels built to your specs for a fraction of the cost of new.
Asking $2000/shipped. Buyer to cover PayPal fees.
Contact me with any questions.
These are high-quality, lightweight forged three-piece wheels that cost over $5k new. The centers have been powdercoated with a beautiful metallic grey, and then clearcoated for durability. The powdercoat job is a 9.5/10; there are a few small imperfections either from dust or that occurred during shipping.
The fronts measure 20x10" with a 1.5" polished lip, and have a slightly more aggressive offset than stock, to give a bit more “poke” (+41). The lips are fully polished and look amazing.
The rears need to be rebuilt to fit a Q7, and here's where you could spec them how you'd like: I could do a standard 10", or a staggered fitment with a 10.5", or even an 11" width in the rear with some pretty aggressive offsets to get a nice flush look. I can vary the lips as well depending on how wide you’d like them.
Note: these wheels were re-drilled from a 120x5 to a 130x5 bolt pattern to fit the Q7. The re-drill job was done by Dominic at Dominant Engineering, who does meticulous work. This is a perfectly safe process: the Q7 is hub-centric, meaning it's the hubs themselves that "support" the weight of the vehicle.
If you're interested, I’d take an initial deposit of 10% via PayPal, and the balance would be due when they’re complete (about two weeks).
This is a great chance to get some high-quality wheels built to your specs for a fraction of the cost of new.
Asking $2000/shipped. Buyer to cover PayPal fees.
Contact me with any questions.
Last edited by nobbyv; 03-03-2017 at 10:10 AM.
Thread
Thread Starter
Forum
Replies
Last Post
S4orce2001
S4 / RS4 (B5 Platform) Discussion
25
06-27-2004 05:58 PM