Anyone have a picture of where the V71 air flap motor is? Also contains the G113 connector
#1
AudiWorld Super User
Thread Starter
Join Date: Oct 2000
Posts: 10,540
Likes: 0
Received 0 Likes
on
0 Posts
Anyone have a picture of where the V71 air flap motor is? Also contains the G113 connector
Looking for a picture of where this motor sits, my A/C is not turning on, and I am thinking of replacing this motor, but want to check it first.
Thanks!
Tom
Thanks!
Tom
#4
AudiWorld Super User
Thread Starter
Join Date: Oct 2000
Posts: 10,540
Likes: 0
Received 0 Likes
on
0 Posts
once again useful as always, I am in a hotel and don't have my bentley on me
thought I would order the part while I am sitting here.
Thanks again for your oh so predictable comment, funny that I even figured you would make such a useful comment before I posted, thanks for once again proving me correct.
Thanks again for your oh so predictable comment, funny that I even figured you would make such a useful comment before I posted, thanks for once again proving me correct.
#5
Here you go Tom
<img src="http://www.msu.edu/~lytleric/V71a.gif">
14 - Service connection
Low pressure side
Used to discharge or charge refrigerant, as well as check refrigerant system pressures.
Note:
Always replace sealing cap after using service connection.
15 - Air flow flap
Removing and installing air flow flap motor -V71-* (with motor position sensor -G113-) page 87-89 .
16 - Fresh air intake duct temperature sensor -G89- **
Removing and installing page 87-88 .
17 - Dust and pollen filter
Removing and installing page 87-121 .
<img src="http://www.msu.edu/~lytleric/V71b.gif">
17 - Instrument panel vent, right
Removing and installing page 87-117 .
18 - Side window defroster vent
Removing and installing.
Repair Manual , Body Interior, Repair Group 70.
19 - Fresh air intake duct temperature sensor -G89- **
Removing and installing page 87-88 .
20 - Air flow flap motor -V71- *
Actuates air flow flap and fresh air / recirculated air flap.
With motor position sensor -G113-.
Removing and installing page 87-89 .
<img src="http://www.msu.edu/~lytleric/R&R1.gif">
Air flow flap motor -V71-, removing and installing
Note:
-V71- operates the air flow flap and fresh/recirculated air flap.
- Remove glove box.
Repair Manual , Body Interior, Repair Group 68.
- Carefully detach actuating arm -A- (for air flow flap) with screwdriver.
<img src="http://www.msu.edu/~lytleric/R&R2.gif">
- Remove bolt -A-.
- Disconnect electrical connection -C-.
- Rotate motor downwards in direction -arrow- and pull out of shaft for fresh/recirculated air flap -B-.
<img src="http://www.msu.edu/~lytleric/R&R3.gif">
Notes on installation:
Replacement motors are supplied set to "recirculated air" mode. To facilitate installation, first connect motor to vehicle electrical system and centralize actuating arm. This is done by switching on the ignition and pressing the "recirculated air" button on the A/C control head to change setting of motor. With the actuating arm centralized, the fresh/recirculated air flap does not touch the limit stops, and the motor can be installed more easily.
- First insert motor into shaft of fresh/recirculated air flap -B-. Then rotate in direction of -arrow-, making sure that lug -D- fits into slot -C-.
After installing, always carry out On Board Diagnostic (OBD) on Climate control page 01-10 .
Route electrical wiring harness so that it cannot come into contact with any moving parts like the actuating arm on the motor or other.
14 - Service connection
Low pressure side
Used to discharge or charge refrigerant, as well as check refrigerant system pressures.
Note:
Always replace sealing cap after using service connection.
15 - Air flow flap
Removing and installing air flow flap motor -V71-* (with motor position sensor -G113-) page 87-89 .
16 - Fresh air intake duct temperature sensor -G89- **
Removing and installing page 87-88 .
17 - Dust and pollen filter
Removing and installing page 87-121 .
<img src="http://www.msu.edu/~lytleric/V71b.gif">
17 - Instrument panel vent, right
Removing and installing page 87-117 .
18 - Side window defroster vent
Removing and installing.
Repair Manual , Body Interior, Repair Group 70.
19 - Fresh air intake duct temperature sensor -G89- **
Removing and installing page 87-88 .
20 - Air flow flap motor -V71- *
Actuates air flow flap and fresh air / recirculated air flap.
With motor position sensor -G113-.
Removing and installing page 87-89 .
<img src="http://www.msu.edu/~lytleric/R&R1.gif">
Air flow flap motor -V71-, removing and installing
Note:
-V71- operates the air flow flap and fresh/recirculated air flap.
- Remove glove box.
Repair Manual , Body Interior, Repair Group 68.
- Carefully detach actuating arm -A- (for air flow flap) with screwdriver.
<img src="http://www.msu.edu/~lytleric/R&R2.gif">
- Remove bolt -A-.
- Disconnect electrical connection -C-.
- Rotate motor downwards in direction -arrow- and pull out of shaft for fresh/recirculated air flap -B-.
<img src="http://www.msu.edu/~lytleric/R&R3.gif">
Notes on installation:
Replacement motors are supplied set to "recirculated air" mode. To facilitate installation, first connect motor to vehicle electrical system and centralize actuating arm. This is done by switching on the ignition and pressing the "recirculated air" button on the A/C control head to change setting of motor. With the actuating arm centralized, the fresh/recirculated air flap does not touch the limit stops, and the motor can be installed more easily.
- First insert motor into shaft of fresh/recirculated air flap -B-. Then rotate in direction of -arrow-, making sure that lug -D- fits into slot -C-.
After installing, always carry out On Board Diagnostic (OBD) on Climate control page 01-10 .
Route electrical wiring harness so that it cannot come into contact with any moving parts like the actuating arm on the motor or other.
Thread
Thread Starter
Forum
Replies
Last Post
SoSlow
Audi Original "S" Cars
1
10-24-2006 12:01 PM